Compaq StorageWorks 64 FW 05.01.00 and SW 07.01.00 HP StorageWorks Embedded We
Summary of contents
- Contents
- About this Guide
- Overview
- Intended Audience
- Related Documentation
- Conventions
- Document Conventions
- Table 1: Document Conventions
- Text Symbols
- Equipment Symbols
- Rack Stability
- Getting Help
- HP Technical Support
- HP Storage Website
- HP Authorized Reseller
- Introduction
- Overview
- Using EWS to Perform Tasks
- Viewing the User Interface
- Figure 1: Example Embedded Web Server page for Edge Switch 2/24
- Benefits
- Key Terms
- Fabric
- Storage Area Network (SAN)
- Zone (Zoning)
- Zone Member
- Zone Set
- Suggested Reading
- Where to Start
- Starting EWS
- Figure 2: Enter Network Password dialog box
- Figure 3: Switch Tab View
- Configuring the Product
- Factory Default Values
- Configuring Ports
- Figure 4: Configure Ports tab view
- Configuring Product Identification
- Figure 5: Configure product Identification tab view
- Configuring Date and Time
- Figure 6: Configure date and time tab view
- Configuring Operating Parameters
- Figure 7: Configure product parameters tab view
- Configuring Fabric Parameters
- Figure 8: Fabric Parameters tab view
- Configuring Network Information
- Figure 9: Configuring network parameters tab view
- Figure 10: Network information message box
- Configuring SNMP
- Figure 11: Configure SNMP parameters tab view
- Enabling or Disabling the CLI
- Figure 12: Disabling the CLI
- Enabling or Disabling Host Control
- Figure 13: Enabling OSMS host control
- Zoning Tab View
- Configuring User Rights
- Figure 14: Configuring user IDs
- User Rights Settings
- Table 2: User Rights Levels
- Binding Ports to Devices
- Figure 15: Configuring Port Binding
- Configuring Open Trunking
- Figure 16: Configuring Open Trunking
- Installing Feature Keys
- Figure 17: Feature Installation tab view
- Configuring Zones
- Understanding Zoning
- Controlling Access Across a Fabric
- Figure 18: Zoning through a single Fibre Channel managed product
- Figure 19: Zoning through a multiswitch fabric
- Controlling Access at the Switch
- Controlling Access at the Server or Storage Device
- Zoning Concepts
- Naming Conventions for Zones and Zone Sets
- Zones
- Using WWNs
- Using Port Numbers
- Default Zone
- Zone Sets
- Active Zone Set
- Merging Zoned Fabrics
- Rules for Merging Zoned Fabrics
- Table 3: Merging Zones
- Configuring, Adding, or Deleting Zones
- Figure 20: Configuring zones
- Figure 21: Modify Zone tab view
- Configuring Zone Sets
- Figure 22: Zone Set tab view
- Viewing Product and Fabric Data
- Viewing Product Information
- Viewing a Representation of the Product
- Figure 23: Switch tab view for an Edge Switch 2/24
- Table 4: State Definitions
- Table 5: Status Indicators
- Viewing Port Properties
- Figure 24: Port Properties tab view
- Viewing FRU Properties
- Figure 25: FRU Properties tab view
- Viewing Unit Properties
- Figure 26: Unit Properties tab view
- Viewing Operating Parameters for the Product
- Figure 27: Operating Parameters tab view
- Viewing Fabric Information
- Viewing Operating Parameters for a Fabric
- Viewing Fabric Directors and Switches
- Figure 28: Fabric tab with Products tab view
- Parts of the Product Cell
- Product Cell Information
- Table 6: Information on the Product Cell
- Parts of the Product Graphic
- Table 7: Operating Status Symbols
- Viewing Fabric Topology
- Figure 29: Fabric tab with Topology tab view
- Table 8: Components of the Topology Page
- Monitoring Products
- Monitoring Ports
- Port List
- Figure 30: Port List tab view
- Port Operational States
- Accessing Port Statistics
- Figure 31: Port Statistics tab view
- Troubleshooting Tip for Port Stats
- Parts of Statistics Tables
- Traffic Transmit and Receive Statistics
- Class 2 Statistics
- Class 3 Statistics
- Error Statistics
- Open Trunking Statistics
- Reviewing the Event Log
- Figure 32: Log tab view
- Severity Levels
- Error Event Code Categories
- Clearing Event Log Entries
- Clearing the System (Product) Error Light
- Viewing Node List
- Figure 33: Node List tab view
- Operating and Managing Products and Parts
- Key Tasks
- Setting Product Beaconing On or Off
- Figure 34: Setting product beaconing
- Setting Product Online or Offline
- Figure 35: Setting product online or offline
- Resetting Product Configuration to Default Values
- Figure 36: Resetting product to default values
- Set Individual Port Beaconing On or Off
- Figure 37: Setting individual port beaconing on or off
- Resetting Ports
- Figure 38: Resetting ports
- Performing Diagnostics on Ports
- Figure 39: Performing diagnostics on ports
- Figure 40: Diagnostics test in progress
- Figure 41: Completed diagnostics test
- Retrieving Maintenance Information
- Figure 42: Retrieving the CTP maintenance information
- Figure 43: Choosing the location to save the CTP maintenance information
- Obtaining Product Information
- Figure 44: Obtaining product information
- Upgrading Firmware
- Figure 45: Upgrading firmware
- Activating (Installing) Optional Features
- Error Messages
- Table 9: Embedded Web Serve Messages
- Index
- A
- B
- C
- D
- E
- F
- G
- H
- I
- K
- L
- M
- N
- O
- P
- R
- S
- T
- U
- V
- W
- Z