IBM 4560SLX manual
Summary of contents
- Contents
- Safety
- Preface
- Product Registration
- Chapter 1. Introduction
- Contents
- Configurations
- Library interfaces
- Front panel
- Magazine doors
- Magazines
- Mail slots
- Power supply
- Tape drives
- Library controller board
- Robotics
- Multi-module library systems
- Chapter 2. Installation
- Setup
- Attaching the slide members to the library
- Attaching the slide members to the rack
- Installing a library in the rack
- SCSI cable configurations
- SCSI interface connectors
- Interface cable specifications
- SCSI configuration
- One tape drive on a single host system
- Two tape drives on a single host system
- Two tape drives on a dual host system
- Multiple libraries on a single host system
- Multiple libraries on a dual host system
- Turning on your library
- Chapter 3. Library configuration
- Setting a SCSI ID
- Setting up reserved tape cartridge slots
- Chapter 4. Operation
- Using the touch screen
- Technical support information
- Mail Slot Access (left magazine only)
- Magazine Access
- Move Media
- LCD contrast controls
- Menu
- View System Data
- Utilities
- Edit Options
- Online
- Status
- Power
- Using tape cartridges
- Removing magazines
- Inserting cartridges into a magazine
- Using the mail slot (left magazines only)
- Bar code labels
- Chapter 5. Maintenance
- Supported media
- Running a cleaning cartridge
- Automatically running a cleaning cartridge
- Manually running a cleaning cartridge
- Running a cleaning cartridge from the mail slot
- Running a cleaning cartridge from a data cartridge slot
- Running a cleaning cartridge from the cleaning slot
- Replacing a cleaning cartridge in a reserved slot
- Replacing a cleaning cartridge in the right magazine
- Replacing a cleaning cartridge in the mail slot
- Chapter 6. Troubleshooting
- Platform problems
- Error recovery procedures (ERPs)
- Fault symptom codes (FSCs)
- Chapter 7. Using the NeoCenter utility
- Establishing communication with your host
- Setting IP addresses
- Setting an access password
- Setting SNMP traps
- Setting e-mail addresses
- Setting remote FTP server parameters
- Setting SCSI parameters
- Setting the SCSI identification
- Setting library parameters
- Setting the drives
- Uploading data
- Downloading data
- Rebooting the library
- Chapter 8. Web TLC
- Operation
- Web TLC access
- Status
- Move media
- Setup
- Functions
- History
- Appendix A. Adding a tape drive
- Appendix B. Adding a library module
- Planning your installation
- Positioning the modules
- Cartridge elevator router
- Router installation
- Installing the cartridge elevator
- Cartridge elevator extension assembly
- Components
- Assembly
- Module configuration
- Configuring the primary master module
- Configuring slave modules
- Cabling and interface connections
- Verifying firmware level of the slave modules
- Fail-over operation
- Cartridge elevator terms
- Cabling considerations for fail-over operation
- Fail-over initiation
- Local fail-over to secondary master initiation
- Remote fail-over to secondary master initiation
- Restoring normal operation
- Local fail-over to primary master
- Remote fail-over to primary master
- Appendix C. Specifications
- Hardware
- Environmental
- Safety
- Electromagnetic emissions
- Electrostatic discharge
- Temperature, humidity, and altitude
- Shock
- Vibration
- Primary power
- Voltage limits
- Frequency limits
- Power requirements
- Sag/Surge protection
- Power line disturbance
- Cooling
- Installation considerations
- Rack mounting
- Input supply
- Grounding
- Appendix D. Field replaceable units (FRUs)
- Appendix E. Warranty information
- Warranty period
- Service and support
- Warranty information on the World Wide Web
- Online technical support
- Telephone technical support
- IBM Statement of Limited Warranty Z125-4753-06 8/2000
- Part 1 - General Terms
- Part 2 - Country-unique Terms
- Appendix F. Notices
- Trademarks
- Electronic emission notices
- Federal Communications Commission (FCC) statement